Programmazione memorie Baofeng UV-5R con CHIRP

[dukone]

Buongiorno a tutti,
vorrei chiedervi una delucidazione in merito alla programmazione con CHIRP.
Ipotizzando che voglia configurare il i seguenti dati

(N)ome   (F)req   shift   tono            regione   (P)rov.   Localita'
  R3     145.675,0    -600 kHz   88,5   9t sicilia   ME   Lipari (ME)

questa programmazione fatta con CHIRP è corretta?



cosa metto su
Tone Mode?
Cross Mode?
ToneSql?
DTCS Code?
Duplex e Offset? mi pare siano giusti...
Mode? esatto pure pare

Grazie cmq per l'aiuto

[i t 9 a c j]

salve da roberto it9acj
il tone lo devi lasciare così come è, no cross mode. il tonesquelch e se vuoi escludere qualche altra comunicazione che e sulla stessa frequenza ma con tono subaudio diverso che fà sentire le comunicazioni insieme a quello del ponte  che stai monitorando. utile questa funzione se ce molto traffico.
dtcs lascialo stare così come è

[ciccio90]

dukone sei om? di dove sei?

[dukone]

Per ora sto solo studiando il funzionamento, che mi intriga molto già da piccolo...
Comunque dalla Sicilia

[ciccio90]

http://imageshack.com/a/img540/37/IKYra3.png ho visto il link che hai postato e ti chiedo di dove sei xk dalle frequenze che hai messo deduco che sei della prov di messina zona tirrenica giusto? paese? anche io della zona scrivimi in privato se vuoi, hai la cartella mp piena

[Carmelo_97]

Nè approfitto del topic per chiedervi a cosa serve la voce Cross Mode

[IU1CRV]

Nè approfitto del topic per chiedervi a cosa serve la voce Cross Mode

Dal wiki di chirp:


Cross Mode
This field controls the squelch behavior of the channel when the Tone Mode is set to Cross. Each value consists of two technologies separated by an arrow (->). The value to the left of the arrow controls the selective-call method used on transmit, while the one to the right of the arrow controls the receive squelch. The possible values are:

Tone: CTCSS tones are used. Transmit tone is taken from the Tone column, receive tone from the ToneSql column.
DTCS: DTCS/DCS codes are used. Transmit code is taken from the DTCS Code column, receive code from the DTCS Rx Code column.
<blank>: Indicates that no method is used for this, either transmit or receive.
The Cross Mode field allows addressing more commercial modes of squelch operation, such as using different tones or codes for transmit and receive. For example:

Tone->Tone: This means use the Tone value for transmit tone, and the ToneSql value for receive squelch
Tone->DTCS: This means use the Tone value for transmit tone, and the DTCS Rx Code value for receive squelch
DTCS->Tone: This means use the DTCS Code value for transmit code, and the ToneSql value for receive squelch
->Tone: This means do not transmit a Tone or DTCS Code, but use the ToneSql value for receive squelch
->DTCS: This means do not transmit a Tone or DTCS Code, but use the DTCS Rx Code value for receive squelch
DTCS->: This means use the DTCS Code value for transmit code, and receive squelch is open or carrier-triggered
DTCS->DTCS: This means use the DTCS Code value for transmit code, and the DTCS Rx Code value for receive squelch


73!  cq

[Carmelo_97]

Nè approfitto del topic per chiedervi a cosa serve la voce Cross Mode

Dal wiki di chirp:


Cross Mode
This field controls the squelch behavior of the channel when the Tone Mode is set to Cross. Each value consists of two technologies separated by an arrow (->). The value to the left of the arrow controls the selective-call method used on transmit, while the one to the right of the arrow controls the receive squelch. The possible values are:

Tone: CTCSS tones are used. Transmit tone is taken from the Tone column, receive tone from the ToneSql column.
DTCS: DTCS/DCS codes are used. Transmit code is taken from the DTCS Code column, receive code from the DTCS Rx Code column.
<blank>: Indicates that no method is used for this, either transmit or receive.
The Cross Mode field allows addressing more commercial modes of squelch operation, such as using different tones or codes for transmit and receive. For example:

Tone->Tone: This means use the Tone value for transmit tone, and the ToneSql value for receive squelch
Tone->DTCS: This means use the Tone value for transmit tone, and the DTCS Rx Code value for receive squelch
DTCS->Tone: This means use the DTCS Code value for transmit code, and the ToneSql value for receive squelch
->Tone: This means do not transmit a Tone or DTCS Code, but use the ToneSql value for receive squelch
->DTCS: This means do not transmit a Tone or DTCS Code, but use the DTCS Rx Code value for receive squelch
DTCS->: This means use the DTCS Code value for transmit code, and receive squelch is open or carrier-triggered
DTCS->DTCS: This means use the DTCS Code value for transmit code, and the DTCS Rx Code value for receive squelch


73!  cq

Ok, grazie 1000